Apprenticeship

Showing all 10 results

  • Placeholder

    Electricity III

    $925.00
    Mondays & Wednesdays (156 Hours-52 sessions) 6:30 pm-9:30 pm Neptune Annex January 10, 2023-May 4, 2023
    Electricity III is the third year of a four-year training program in preparation for the state license exam. This is a theory class. Books, supplies and personal safety equipment are not included. Prerequisite: Electricity II. Certificates will not be issued for attendance less than 144 hrs. Topics covered: wiring devices, load calculations-branch circuits, motor controls, conductor selection & calculations, overcurrent protection, distribution equipment, raceway, box & fitting fill requirements, distribution, system transformers, lamps, ballasts, & components, motor calculations, motor maintenance-part one, and electricit ...read more
    Select options
  • Placeholder

    Electricity IV

    $925.00
    Mondays & Wednesdays (156 Hours-52 sessions) 6:00 pm-9:00 pm Aberdeen October 3, 2022-May 3, 2023
    Electricity IV is the fourth year of a four-year training program in preparation for the state license exam. This is a theory class. Books, supplies, and personal safety equipment not included. Prerequisite: Electricity III. Certificates will not be issued for attendance less than 144 hrs. Topics covered: load calculations-feeders & services, advanced controls, practical applications of lighting, HVAC controls, standby & emergency systems, welding machines, basic electronic theories, fire alarm systems, heat tracing & freeze protection, specialty transformers, motor maintenance-part two, high voltage termination. ...read more
    Select options
  • Placeholder

    HVAC/R II

    $925.00
    Mondays & Wednesdays (156 Hours)
    6:00 pm-9:00 pm Freehold
    October 3, 2022-May 3, 2023
    HVAC/R II is the second year of a four-year training program. Registered Apprenticeship is not necessary to register for this class. This is a theory class. Books, supplies, and personal safety equipment not included. Prerequisite: HVAC/R I. Certificates will not be issued for attendance less than 144 hrs. Topics covered: review from first year, safety, A/C systems, heat pumps, EPA certification, recovery, leak detection, air distribution, and residential load calculations. ...read more
    Select options
  • Placeholder

    HVAC/R III

    $925.00
    Mondays & Wednesdays (156 Hours)
    6:30 pm-9:30 pm Middletown
    October 3, 2022-May 3, 2023
    HVAC/R III is the third year of a four-year training program. Registered Apprenticeship is not necessary to register for the class. This is a theory class. Books, supplies, and personal safety equipment not included. Prerequisite: HVAC/R II. Topics covered: preventive maintenance, steam systems, intro to electrical troubleshooting, customer relations, commercial heating and cooling, water and air balance. ...read more
    Select options
  • Placeholder

    HVAC/R IV

    $925.00
    Mondays & Wednesdays (156 Hours) 6:00 pm-9:00 pm Aberdeen October 3, 2022-May 3, 2023
    This program includes basic safety, rigging, trade mathematics, blueprint reading, basic electricity, introduction to cooling and heating, installation practices, refrigeration and air conditioning, air movements, maintenance skills, compressors and heat pumps, hydronic systems, light and heavy commercial, sheet metal, service and troubleshooting of systems. Includes focus on codes necessary for the successful completion of the Environmental Protection Agency (EPA) 608 Universal Certification exam. This is a theory class. Books, supplies, and personal safety equipment not included. Prerequisite: HVAC/R III. ...read more
    Select options
  • Placeholder

    Plumbing II

    $925.00
    Mondays & Wednesdays (156 Hours) 6:00 pm-9:00 pm Neptune Annex October 3, 2022-May 3, 2023
    Plumbing II is the second year of a four-year training program. The program is focused on the needs of the plumbing apprentice. This is a theory class. Books, supplies and personal safety equipment are not included. Prerequisite: Plumbing I. Certificates will not be issued for attendance less than 144 hrs. Topics covered: reading commercial drawings, intermediate math, installing & testing DWV piping, installing water heaters, installing & testing water supply piping. ...read more
    Select options
  • Placeholder

    Plumbing III

    $925.00
    Mondays and Wednesdays (156 Hours) 6:00 pm-9:00 pm Neptune Annex October 3, 2022-May 3, 2023
    Plumbing III is the third year of a four-year training program. This is a theory class. Books, supplies and personal safety equipment are not included. Prerequisite: Plumbing II. Certificates will not be issued for attendance less than 144 hrs. Topics covered: intro to regional & local plumbing codes, fixture rough-in, backflow preventers, advance math for plumbers, installing water supply piping, types of vents and venting, thawing frozen water pipes, indirect & special waste, sizing, piping, venting natural gas systems, and portable water system. ...read more
    Select options
  • Placeholder

    Plumbing IV

    $925.00
    Tuesdays and Thursdays (156 Hours) 6:00 pm-9:00 pm Career Center October 3, 2022-May 3, 2023
    Plumbing IV is the fourth year of a four-year training program. This is a theory class. Books, supplies, and personal safety equipment not included. Prerequisite: Plumbing III. Certificates will not be issued for attendance less than 144 hrs. Topics covered: plumbing theory, on-the-job task organization, sizing storm drainage, sizing vents, sizing drainage systems, combination waste & vent systems, sizing water supply pipes, servicing plumbing fixtures, installing pools/hot tubs, compressed air piping, hydronic heating, private waste disposals, private water supply, mobile home plumbing and mobile home parks. ...read more
    Select options
  • Placeholder

    Waste Water Maintenance Mechanic Apprenticeship

    $0.00
    Waste/Water Water Technology (Introduction) Click here for class details and to register Mondays, Tuesdays, Wednesdays (45 sessions) 5:00 pm to 9:00 pm Tinton Falls October 3, 2022-January 31, 2023 Electricity I Click here for class details and to register Mondays & Wednesdays (156 Hours) 6:30 pm to 9:30 pm Neptune Annex October 3, 2022-May 3, 2023 Plumbing I Click here for class details and to register Tuesdays & Thursdays (156 Hours) 6:30 pm to 9:30 pm Neptune Annex October 5, 2021-April 28, 2022 Welding I Click here for class details and to register Mondays & Wednesdays (22 Sessions) 4:00 pm to 7:00 pm Aberdeen September 19, 2022-December 14, 2023 Welding II Click here for class details and to register Tuesdays & Thursdays (22 sessions) 4:00 pm to 7:00 pm Aberdeen September 27, 2022-December 15, 2022 Machine Shop I: This 60-hour course is available at Middlesex County Vocational & Technical Schools. Call for (732) 257-3300 ext. 1925 for more information.
    This 660-hour apprenticeship program focuses on set-up and operations of a variety of machine tools, fitting and assembling parts to fabricate or repair machine tools and maintaining industrial machines. Students will apply knowledge of mechanics, shop mathematics, metal properties, layout and machine procedures. Dismantling machines or equipment, using hand tools or power tools to examine parts for defect or to remove defective parts will be covered. Students will learn how to weld parts, using arc or gas welding equipment, repair or replace faulty wiring, switches or relays.

    This is a four-year program. The classes listed may be taken in any sequence, except for <span style="text-deco ...read more

    Add to cart
  • Placeholder

    Wastewater-Treatment Plant Operator Apprenticeship

    $0.00
    Year One: NOW AVAILABLE TO REGISTER! Waste/Water Water Technology (Introduction) Click here to register Mondays, Tuesdays, Wednesdays (45 sessions) 5:00 pm to 9:00 pm Tinton Falls September 19, 2022 - January 18, 2023 - $1,350 Year Two: Registration TBA Advanced Waste Water (Introduction) Prerequisite: Water/Waster Water Technology or S-1 License. DATES TBD 5:00 pm to 9:00 pm Year Three: Registration TBA Advanced Collections Tuesdays & Thursdays (13 sessions) 5:00pm to 9:00 pm Aberdeen September 27, 2023 - November 8, 2021
    This 315-hour apprenticeship program focuses on operations in sewage treatment, sludge processing, and disposal equipment in wastewater treatment to control flow and processing of sewage. Topics that will be covered include: monitoring control panels, adjusting valves and gates manually or by remote control to regulate sewage flow, observing variation in operating conditions and interpreting meter and gauge readings, and test results to determine load requirements, starting and stopping pumps, engines, and generators to control flow of raw sewage through filtering, settling, aeration and sludge digestion processes. Other mechanical duties covered as assigned. This is a three-year ...read more
    Add to cart